change location
321-802-5889
321-733-7477
Model or part number: 1-101-250-03
About this product
1 hole on ea blade groove,2 holes equally spaced 0.065 in. Min,0.070 in. Max dia,8 holes equally spaced 0.120 in. Nom dia,10 holes equally spaced,12 holes equally spaced 0.330 min,0.337 max dia,16 holes equally spaced,34 places
Turbine Engine Axial Compressor Disk And Hub NSN 2840-00-176-3746. Compressor rotor
NSN 2840-00-176-3746 Datasheet
Factory New, New Material, New Surplus, Overhauled, Serviceable, Repairable, and AS Removed / Used material will be accompanied by a Certificate of Conformance, and any other documents/trace when applicable. We have a 7 year record retention.
We are committed to quality and follow an AS9120 quality management system. AeroBase Group is HAZMAT certified and registered with DDTC,
ITAR, and Aviation Suppliers Association (ASA). All products are 100% inspected.
Quality Commitment »
Delivery of IN-STOCK orders ship same-day when order is placed before 2:00 PM EST.
Delivery dates for NON-STOCK items are estimates based on current backlog and are subject to confirmation at the time of order.
Inc 61831 cancelled/replaced by ,inc 50561, fiig a10700, app-key f ,inc 50562, fiig a10700, app-key f ,inc 50563, fiig a10700, app-key f ,inc 50564, fiig a10700, app-key f ,inc 50565, fiig a10700, app-key f ,inc 50566, fiig a10700, app-key f ,on 021513 ~(all except usa). A disk having provisions on the outer periphery for attaching compressor blades and an integral hub that provides support and alignment for the compressor rotor. See also disk,axial compressor,turbine engine.
Packing shall be accomplished in accordance with table c.Ii for the packing level specified. closure, sealing and reinforcement shall be in accordance with applicable specification for shipping container.
Packing is not required. the unit container shall also serve as the shipping container. closure, sealing and reinforcement shall be in accordance with applicable specification for shipping container.
Items or packages that require packing for acceptance by the carrier shall be packed in exterior type shipping containers in a manner that will ensure safe transportation at the lowest rate to the point of delivery and shall meet, as a minimum, the requirements of the following rules and regulations, as applicable to the mode(s) of transportation to be utilized: (a) postal regulations, (b) department of transportation regulations, (c) civil air regulations, (d) uniform freight classification rules, (e) national motor freight classification rules, (f) american truckers' association rules, (g) other applicable carriers' rules, (h) military air regulations for dangerous materials. consolidation of shipments. all exterior packs of 1.5 cubic feet or less having no single dimension (length, width, height) exceeding 40 inches (and when the total number of such containers in any individual shipment exceeds 25), shall be consolidated, using flat pallets, box pallets, or containers as the consolidating media. dangerous goods shall be prepared for shipment according to applicable department of transportation (dot) regulations and international regulations in effect at time of shipment. shipment by parcel post must comply with postal regulations.
All packaging data is mandatory for compliance and no substitutions are permitted. fast packs should be included in this category.
No special marking.
Unheated general purpose.
Waterproof bag, sealed.
Ppp-c-795, class 1, cellular plastic film cushioning.
No requirement.
Parts Of Gas Turbine Aircraft Engines, Other Than For Use In Civil Aircraft
Engines and Turbines For Military Aircraft
Parts For Gas Turbines, N.e.s.
No special type of cargo code applicable.
Vehicle parts, other than automobile.
Supplies and equipment for aircraft and aerial targets, including aircraft and maintenance parts, aircraft accessories, aircraft.
Shipment is not a consolidation and does not exceed 84 inches in any dimension.
Other or no special handling required (sh)
| Code | Definition |
|---|---|
| FN | Factory New. Parts manufactured by the OEM and includes manufacturer certification. |
| NE | New. Parts manufactured by the OEM. May include manufacturer certification or company certification. |
| NS | New Surplus. New material item purchased from excess inventory. |
| OH | Overhauled. Product has been rebuilt and tested in accordance with the manufacturer's specifications by a repair shop (MRO). |
| SV | Serviceable product. |
| AR | As Removed. Product removed from aircraft or platform with no guarentee on the functionality of the part. |
| RP | Repairable. Product can be repaired by a MRO and be given a FAA 8130 or EASA Form 1 certification. |
| Part Number | RNVC | RNAAC | DAC | CAGE |
|---|---|---|---|---|
| 1-101-250-03 | 2 | CT | 1 | 99193 |
| Name | No. Items | |||
|---|---|---|---|---|
| [You must be logged in to use lists] | ||||