change location
321-802-5889
321-733-7477
Model or part number: 58745-1
Adjusting Stud Shaft NSN 3040-01-183-4611.
NSN 3040-01-183-4611 Datasheet
Factory New, New Material, New Surplus, Overhauled, Serviceable, Repairable, and AS Removed / Used material will be accompanied by a Certificate of Conformance, and any other documents/trace when applicable. We have a 7 year record retention.
We are committed to quality and follow an AS9120 quality management system. AeroBase Group is HAZMAT certified and registered with DDTC,
ITAR, and Aviation Suppliers Association (ASA). All products are 100% inspected.
Quality Commitment »
Delivery of IN-STOCK orders ship same-day when order is placed before 2:00 PM EST.
Delivery dates for NON-STOCK items are estimates based on current backlog and are subject to confirmation at the time of order.
| NSN | Component Description |
|---|---|
| NSN 5342-01-168-1896 | Weapon System Access Door |
| NSN 3810-01-168-2017 | Crane Guide Roller |
| NSN 3810-01-168-2018 | Roller Guide Assembly |
| NSN 3810-01-168-2019 | Crane Guide Roller |
| NSN 4730-01-168-6407 | Tube To Boss Elbow |
| NSN 3040-01-169-7321 | Shouldered Shaft |
| NSN 3810-01-169-7677 | Roller Guide Assembly |
| NSN 3810-01-169-7678 | Crane Roller Guide Frame |
| NSN 3810-01-169-7679 | Crane Guide Roller Frame |
| NSN 3815-01-169-8704 | Center Section Turntable |
| NSN 3815-01-169-8705 | Fly Section Weldment |
| NSN 2930-01-170-1666 | Engine Water Outlet |
| NSN 3810-01-170-2502 | Wear Pad |
| NSN 3810-01-170-2503 | Wear Pad |
| NSN 3040-01-170-2504 | Planetary Gear |
| NSN 2590-01-170-2505 | Output Planet Carrier |
| NSN 2590-01-170-2506 | Support End Plate |
| NSN 2590-01-170-2507 | Hoist Base |
| NSN 3810-01-170-2508 | Motor Pilot |
| NSN 3810-01-170-2509 | Motor Brake And Reducer Assembly |
| NSN 3810-01-170-2511 | Cylinder Housing |
| NSN 2530-01-170-2536 | Brake Disc |
| NSN 3040-01-170-2540 | Linear Actuating Cylinder Piston |
| NSN 3020-01-170-2557 | Internal Gear |
| NSN 2590-01-170-4733 | Vehicular B Hydraulic Hoist Unit |
| NSN 3810-01-170-9219 | Crane Turntable Drive Assembly |
| NSN 3010-01-170-9283 | Speed Decreaser Gear Assembly |
| NSN 3815-01-170-9497 | Line Actuating Cylinder Assembly |
| NSN 2510-01-171-2047 | Vehicular Frame |
| NSN 2520-01-171-2214 | Remote Control Lever |
| NSN 4320-01-171-4448 | Mecha Seal Replacement Parts Kit |
| NSN 3040-01-171-4993 | Straight Shaft |
| NSN 4820-01-171-5047 | Flow Control Valve |
| NSN 3810-01-171-5064 | Outrigger Wear Pad |
| NSN 2590-01-171-5065 | Wear Pad |
A straight shaft having two or more of the following conditions: a specified surface finish designation in the range of 1 to 125 microinches (o.O25 to 3.2 micrometers), arithmetical average (aa), machined peripheral flat(s), circular groove (s), keyway(s), splines, threads, or holes. It is not designed for use in aligning by fitting into corresponding holes of another item. It may be drilled for lubricating holes. For items having an integral gear(s) or worm(s), see gearshaft (as modified). For items designed to support rotating members see axle(1), straight. For items not having the above conditions see pin, straight, headless. For items having machined ends which constitute steps see shaft(1), shouldered; axle(1), shouldered; and bolt, fluid passage.
Packing shall be accomplished in accordance with table c.Ii for the packing level specified. closure, sealing and reinforcement shall be in accordance with applicable specification for shipping container.
Packing shall be accomplished in accordance with table c.Ii for the packing level specified. closure, sealing and reinforcement shall be in accordance with the appropriate shipping container specification.
Options can be exercised as to specific method of preservation or dod approved packaging materials to be used. however, basic preservation method shall be retained, supplemental data shall be complied with, and unit package dimensions shall not be increased by more than one inch. equal or better protection shall be given the item and there shall be no increase in the package cost.
No special marking.
Preservative coating only (with greaseproof wrap, as required).
Transmission Shafts and Cranks, Except Camshafts and Crankshafts
Industrial Machines, Other
Transmission Shafts (including Cam and Crank Shafts) and Cranks
No special type of cargo code applicable.
Motors and parts, (machinery and parts),(less than 35 feet).
Trailers, vehicles, machinery, shop and warehouse equipment and supplies including special tools and equipment, ground servicing.
Shipment is not a consolidation and does not exceed 84 inches in any dimension.
Other or no special handling required (sh)
| Code | Definition |
|---|---|
| FN | Factory New. Parts manufactured by the OEM and includes manufacturer certification. |
| NE | New. Parts manufactured by the OEM. May include manufacturer certification or company certification. |
| NS | New Surplus. New material item purchased from excess inventory. |
| OH | Overhauled. Product has been rebuilt and tested in accordance with the manufacturer's specifications by a repair shop (MRO). |
| SV | Serviceable product. |
| AR | As Removed. Product removed from aircraft or platform with no guarentee on the functionality of the part. |
| RP | Repairable. Product can be repaired by a MRO and be given a FAA 8130 or EASA Form 1 certification. |
| Part Number | RNVC | RNAAC | DAC | CAGE |
|---|---|---|---|---|
| 58745-1 | 9 | AX | E | 82366 |
| Name | No. Items | |||
|---|---|---|---|---|
| [You must be logged in to use lists] | ||||