change location
321-802-5889
321-733-7477
Model or part number: 87011A0630-1
Adjusting Stud Shaft NSN 3040-01-563-5061.
NSN 3040-01-563-5061 Datasheet
Factory New, New Material, New Surplus, Overhauled, Serviceable, Repairable, and AS Removed / Used material will be accompanied by a Certificate of Conformance, and any other documents/trace when applicable. We have a 7 year record retention.
We are committed to quality and follow an AS9120 quality management system. AeroBase Group is HAZMAT certified and registered with DDTC,
ITAR, and Aviation Suppliers Association (ASA). All products are 100% inspected.
Quality Commitment »
Delivery of IN-STOCK orders ship same-day when order is placed before 2:00 PM EST.
Delivery dates for NON-STOCK items are estimates based on current backlog and are subject to confirmation at the time of order.
| NSN | Component Description |
|---|---|
| NSN 6115-01-503-1111 | Direct Current Generator |
| NSN 3010-01-503-1133 | Speed Decreaser Gear Assembly |
| NSN 6110-01-503-2378 | Motor Controller |
| NSN 6145-01-503-2394 | Electrical Special Purpose Cable |
| NSN 5305-01-503-2540 | Machine Screw |
| NSN 5905-01-503-2562 | Pre Wire Wound Variable Resistor |
| NSN 5305-01-503-2930 | Machine Screw |
| NSN 5935-01-503-3140 | Electrical Connector Shell |
| NSN 6145-01-503-3170 | Electrical Special Purpose Cable |
| NSN 5330-01-503-3174 | Gasket |
| NSN 5340-01-503-3177 | Clamp Bolt Assembly |
| NSN 3130-01-503-3182 | Bearing Flanged |
| NSN 6210-01-503-3191 | Light Emitting Diode |
| NSN 5305-01-503-3335 | Hexagon Head Cap Screw |
| NSN 5306-01-503-3347 | Eye Bolt |
| NSN 5920-01-503-3364 | Cartridge Fuse |
| NSN 2530-01-503-4075 | Brake Disc |
| NSN 5340-01-503-5234 | Casement Fastener |
| NSN 5315-01-503-9346 | Cotter Pin |
| NSN 3040-01-503-9348 | Disk Brake Shoe |
| NSN 5360-01-503-9353 | Compression Helical Spring |
| NSN 1680-01-503-9355 | Control Lever |
| NSN 5975-01-504-4249 | Electrical Box Connector |
| NSN 5360-01-562-9608 | Compression Helical Spring |
| NSN 5305-01-562-9705 | Machine Screw |
| NSN 5305-01-562-9713 | Machine Screw |
| NSN 5310-01-562-9717 | Flat Washer |
| NSN 5310-01-562-9719 | Hexagon Self-locking Nut |
| NSN 5340-01-562-9816 | Dust And Moisture Protective Cap |
| NSN 5305-01-562-9818 | Socket Head Cap Screw |
| NSN 5305-01-562-9821 | Socket Head Cap Screw |
| NSN 5999-01-562-9836 | Electrical-electronic Heat Sink |
| NSN 5305-01-562-9856 | Machine Screw |
| NSN 5920-01-562-9996 | Cartridge Fuse |
| NSN 6240-01-563-0030 | Incandescent Lamp |
A straight shaft having two or more of the following conditions: a specified surface finish designation in the range of 1 to 125 microinches (o.O25 to 3.2 micrometers), arithmetical average (aa), machined peripheral flat(s), circular groove (s), keyway(s), splines, threads, or holes. It is not designed for use in aligning by fitting into corresponding holes of another item. It may be drilled for lubricating holes. For items having an integral gear(s) or worm(s), see gearshaft (as modified). For items designed to support rotating members see axle(1), straight. For items not having the above conditions see pin, straight, headless. For items having machined ends which constitute steps see shaft(1), shouldered; axle(1), shouldered; and bolt, fluid passage.
Packing shall be accomplished in accordance with table c.Ii for the packing level specified. closure, sealing and reinforcement shall be in accordance with applicable specification for shipping container.
Packing shall be accomplished in accordance with table c.Ii for the packing level specified. closure, sealing and reinforcement shall be in accordance with the appropriate shipping container specification.
Options can be exercised as to specific method of preservation or dod approved packaging materials to be used. however, basic preservation method shall be retained, supplemental data shall be complied with, and unit package dimensions shall not be increased by more than one inch. equal or better protection shall be given the item and there shall be no increase in the package cost.
No special marking.
Preservative coating only (with greaseproof wrap, as required).
No requirement.
Vendor's protective grease or oil coating.
Transmission Shafts and Cranks, Except Camshafts and Crankshafts
Industrial Machines, Other
Transmission Shafts (including Cam and Crank Shafts) and Cranks
No special type of cargo code applicable.
Motors and parts, (machinery and parts),(less than 35 feet).
Trailers, vehicles, machinery, shop and warehouse equipment and supplies including special tools and equipment, ground servicing.
Shipment is not a consolidation and does not exceed 84 inches in any dimension.
Other or no special handling required (sh)
| 02/16 |
|---|
| 19.00 |
| Code | Definition |
|---|---|
| FN | Factory New. Parts manufactured by the OEM and includes manufacturer certification. |
| NE | New. Parts manufactured by the OEM. May include manufacturer certification or company certification. |
| NS | New Surplus. New material item purchased from excess inventory. |
| OH | Overhauled. Product has been rebuilt and tested in accordance with the manufacturer's specifications by a repair shop (MRO). |
| SV | Serviceable product. |
| AR | As Removed. Product removed from aircraft or platform with no guarentee on the functionality of the part. |
| RP | Repairable. Product can be repaired by a MRO and be given a FAA 8130 or EASA Form 1 certification. |
| Part Number | RNVC | RNAAC | DAC | CAGE |
|---|---|---|---|---|
| 87011A0630-1 | 2 | ZZ | 5 | 1U339 |
| 87011A0630-1 | 2 | ZZ | 5 | 3F4L6 |
| 87011A0630-1 | 2 | ZZ | 5 | 8W529 |
| Name | No. Items | |||
|---|---|---|---|---|
| [You must be logged in to use lists] | ||||