Model or part number: MIL-R-44035
Factory New, New Material, New Surplus, Overhauled, Serviceable, Repairable, and AS Removed / Used material will be accompanied by a Certificate of Conformance, and any other documents/trace when applicable. We have a 7 year record retention.
We are committed to quality and follow an AS9120 quality management system. AeroBase Group is HAZMAT certified and registered with DDTC,
ITAR, and Aviation Suppliers Association (ASA). All products are 100% inspected.
Quality Commitment »
Delivery of IN-STOCK orders ship same-day when order is placed before 2:00 PM EST.
Delivery dates for NON-STOCK items are estimates based on current backlog and are subject to confirmation at the time of order.
NSN | Component Description |
---|---|
NSN 5930-01-240-8118 | Sensitive Switch |
NSN 4710-01-250-1872 | Tube Assembly |
NSN 4710-01-250-1873 | Tube Assembly |
NSN 4710-01-250-1875 | Tube Assembly |
NSN 4730-01-258-8083 | Snap On Connector |
NSN 4810-01-361-3912 | Solenoid Valve |
NSN 2990-01-361-3967 | Engine Air Duct Heater |
NSN 3020-01-361-4998 | Groove Pulley |
NSN 6685-01-362-4820 | Indicating Temperature Control |
NSN 4140-01-363-4662 | Axial Fan Impeller |
NSN 6150-01-369-1610 | E Special Purpose Cable Assembly |
NSN 6150-01-369-1611 | E Special Purpose Cable Assembly |
NSN 6150-01-369-1612 | E Special Purpose Cable Assembly |
NSN 6150-01-369-2353 | E Special Purpose Cable Assembly |
NSN 6105-01-371-6948 | Alternating Current Motor |
NSN 4820-01-425-8690 | Saddle Valve |
A self-contained refrigeration unit having a power driven compressor, condenser, evaporator, and other necessary components. It is used to refrigerate an enclosed space by the introduction of the evaporator section through an opening in the side or top of the enclosure forming an integral section thereof (panel type) or placed in the outside proximity of the inclosure (remote type). Excludes refrigerator-freezer, mechanical, food; and refrigerator, mechanical, food.
Packing shall be accomplished to meet the performance test requirements of astm-d4169, distribution cycle 18, assurance level 1.
Packing shall be accomplished in accordance with table c.Ii for the packing level specified. closure, sealing and reinforcement shall be in accordance with the appropriate shipping container specification.
Items or packages that require packing for acceptance by the carrier shall be packed in exterior type shipping containers in a manner that will ensure safe transportation at the lowest rate to the point of delivery and shall meet, as a minimum, the requirements of the following rules and regulations, as applicable to the mode(s) of transportation to be utilized: (a) postal regulations, (b) department of transportation regulations, (c) civil air regulations, (d) uniform freight classification rules, (e) national motor freight classification rules, (f) american truckers' association rules, (g) other applicable carriers' rules, (h) military air regulations for dangerous materials. consolidation of shipments. all exterior packs of 1.5 cubic feet or less having no single dimension (length, width, height) exceeding 40 inches (and when the total number of such containers in any individual shipment exceeds 25), shall be consolidated, using flat pallets, box pallets, or containers as the consolidating media. dangerous goods shall be prepared for shipment according to applicable department of transportation (dot) regulations and international regulations in effect at time of shipment. shipment by parcel post must comply with postal regulations.
Options can be exercised as to specific method of preservation or dod approved packaging materials to be used. however, basic preservation method shall be retained, supplemental data shall be complied with, and unit package dimensions shall not be increased by more than one inch. equal or better protection shall be given the item and there shall be no increase in the package cost.
No special marking.
Unheated general purpose.
Physical protection.
Wood blocking and bracing, fasteners, or steel strapping, for tie-down purposes. rubber tired wheels shall be blocked clear of the floor of the crate or skid and shall not be load bearing.
No requirement.
Refrigerating Or Freezing Equipment, Nesoi
Photo, Service Industry Machinery
Refrigerating Or Freezing Equipment, N.e.s.; Heat Pumps
No special type of cargo code applicable.
Engineer and material handling equipment, test/tool sets and equipment.
Office and school supplies and equipment including office machines, furniture and stationary..
Shipment is not a consolidation, but does exceed 84 inches in one or more dimensions.
Other or no special handling required (sh)
Code | Definition |
---|---|
FN | Factory New. Parts manufactured by the OEM and includes manufacturer certification. |
NE | New. Parts manufactured by the OEM. May include manufacturer certification or company certification. |
NS | New Surplus. New material item purchased from excess inventory. |
OH | Overhauled. Product has been rebuilt and tested in accordance with the manufacturer's specifications by a repair shop (MRO). |
SV | Serviceable product. |
AR | As Removed. Product removed from aircraft or platform with no guarentee on the functionality of the part. |
RP | Repairable. Product can be repaired by a MRO and be given a FAA 8130 or EASA Form 1 certification. |
Part Number | RNVC | RNAAC | DAC | CAGE |
---|---|---|---|---|
MIL-R-44035 | 1 | PA | 4 | 81349 |
ERU-4E | 2 | PA | 5 | 11718 |
835022A0000 | 2 | PA | 1 | 01365 |
EREL-40A | 9 | PA | 1 | 60569 |
MIL-R-44035 | 1 | PA | 4 | 81349 |
ERU-4E | 2 | PA | 5 | 11718 |
835022A0000 | 2 | PA | 1 | 01365 |
EREL-40A | 9 | PA | 1 | 60569 |
MIL-R-44035 | 1 | PA | 4 | 81349 |
ERU-4E | 2 | PA | 5 | 11718 |
835022A0000 | 2 | PA | 1 | 01365 |
EREL-40A | 9 | PA | 1 | 60569 |
MIL-R-44035 | 1 | PA | 4 | 81349 |
ERU-4E | 2 | PA | 5 | 11718 |
835022A0000 | 2 | PA | 1 | 01365 |
EREL-40A | 9 | PA | 1 | 60569 |
Name | No. Items | |||
---|---|---|---|---|
[You must be logged in to use lists] |