Model or part number: 43943
About this product
Washer,slack adjusted
Riveting Burr NSN 5310-01-512-9502.
Factory New, New Material, New Surplus, Overhauled, Serviceable, Repairable, and AS Removed / Used material will be accompanied by a Certificate of Conformance, and any other documents/trace when applicable. We have a 7 year record retention.
We are committed to quality and follow an AS9120 quality management system. AeroBase Group is HAZMAT certified and registered with DDTC,
ITAR, and Aviation Suppliers Association (ASA). All products are 100% inspected.
Quality Commitment »
Delivery of IN-STOCK orders ship same-day when order is placed before 2:00 PM EST.
Delivery dates for NON-STOCK items are estimates based on current backlog and are subject to confirmation at the time of order.
NSN | Component Description |
---|---|
NSN 5330-01-157-8826 | Hydra Cylinder Seal |
NSN 5330-01-157-8827 | Hydraulic Cylinder Seal |
NSN 4910-01-158-3941 | Installing Tool |
NSN 4910-01-158-3954 | Removing An Swaging |
NSN 5340-01-158-3957 | Mounting Bracket |
NSN 4910-01-158-3961 | Swaging Tool |
NSN 4910-01-158-3963 | Swaging Tool Holder |
NSN 4910-01-158-3974 | Ring Compressor |
NSN 4910-01-171-8243 | Bushing Ram |
NSN 2520-01-187-1264 | Differential Carrier Head Assemb |
NSN 2520-01-187-2266 | Differential Carrier Head Assemb |
NSN 2520-01-188-1278 | Differential Carrier Head Assemb |
NSN 2990-01-205-8755 | Governor Housing Assembly |
NSN 2990-01-205-8756 | Governor Housing |
NSN 2815-01-205-8758 | Diesel Engi Cylinder Block Plate |
NSN 4820-01-205-8766 | Valve Body |
NSN 2990-01-205-8768 | Diesel Engine Governor |
NSN 2815-01-205-9412 | Turbo Charger Blower Assembly |
NSN 2815-01-205-9413 | Crankshaft Stablizer |
NSN 2990-01-205-9449 | Exhaust Pipe Connector |
NSN 2990-01-205-9450 | Exhaust Pipe Connector |
NSN 2930-01-205-9456 | Engine Water Outlet |
NSN 2815-01-206-0873 | Vibration Damper Hub |
NSN 4910-01-206-4490 | Injector Dam Assembly |
NSN 2815-01-207-2493 | Supply Housing Assembly |
NSN 2940-01-207-3718 | Engine Intake Filter |
NSN 2920-01-207-9925 | Alternator Plate Housing |
NSN 2910-01-208-2207 | Remote Control Lever |
NSN 2815-01-208-9387 | Engine Crankshaft |
NSN 2530-01-209-0890 | Compressor Crankcase |
NSN 5340-01-210-0334 | Access Cover |
NSN 5930-01-210-5399 | Electrical Switch Retainer |
NSN 4140-01-211-0957 | Axial Fan Impeller |
NSN 2520-01-211-1000 | Differential Carrier Cover |
NSN 2520-01-211-1001 | Carrier And Cap Assembly |
A washer having a centrally located hole with a solid or laminated cross-section and two flat parallel bearing surfaces. The hole must be 75 percent or less than the largest dimension and the bearing surface finish is greater than 32 microinch (0.8 micrometer). The thickness cannot exceed 25 percent of the largest outside dimension. When the largest outside dimension is less than 1/4 inch or 6mm, the thickness must be 0.006 inches (0.15mm) or greater and for items 1/4 inch (6mm) or larger, the thickness must be 0.016 inches (0.4mm) or greater. The maximum tolerance is applied to dimensions and used as a determining factor. Items with separable lamination use shim. For items fabricated from ceramic or electrically rated materials by specification or industry standards use insulator (1), washer. Excludes disk, valve, graphite impregnated and lubricated items.
Packing shall be accomplished to meet the performance test requirements of astm-d4169, distribution cycle 18, assurance level 1.
Packing shall be accomplished in accordance with table c.Ii for the packing level specified. closure, sealing and reinforcement shall be in accordance with the appropriate shipping container specification.
Options can be exercised as to specific method of preservation or dod approved packaging materials to be used. however, basic preservation method shall be retained, supplemental data shall be complied with, and unit package dimensions shall not be increased by more than one inch. equal or better protection shall be given the item and there shall be no increase in the package cost.
No special marking.
Physical protection.
No requirement.
No requirement.
No special type of cargo code applicable.
Metal and metal products, nos, (less than 35 feet).
Trailers, vehicles, machinery, shop and warehouse equipment and supplies including special tools and equipment, ground servicing.
Shipment is not a consolidation and does not exceed 84 inches in any dimension.
Other or no special handling required (sh)
Code | Definition |
---|---|
FN | Factory New. Parts manufactured by the OEM and includes manufacturer certification. |
NE | New. Parts manufactured by the OEM. May include manufacturer certification or company certification. |
NS | New Surplus. New material item purchased from excess inventory. |
OH | Overhauled. Product has been rebuilt and tested in accordance with the manufacturer's specifications by a repair shop (MRO). |
SV | Serviceable product. |
AR | As Removed. Product removed from aircraft or platform with no guarentee on the functionality of the part. |
RP | Repairable. Product can be repaired by a MRO and be given a FAA 8130 or EASA Form 1 certification. |
Part Number | RNVC | RNAAC | DAC | CAGE |
---|---|---|---|---|
43943 | 2 | ZZ | 5 | 1MVZ1 |
43943 | 2 | ZZ | 5 | 1MVZ1 |
43943 | 2 | ZZ | 5 | 1MVZ1 |
Name | No. Items | |||
---|---|---|---|---|
[You must be logged in to use lists] |