change location
321-802-5889
321-733-7477
Model or part number: 12759-01274
Riveting Burr NSN 5310-01-535-4831.
NSN 5310-01-535-4831 Datasheet
Factory New, New Material, New Surplus, Overhauled, Serviceable, Repairable, and AS Removed / Used material will be accompanied by a Certificate of Conformance, and any other documents/trace when applicable. We have a 7 year record retention.
We are committed to quality and follow an AS9120 quality management system. AeroBase Group is HAZMAT certified and registered with DDTC,
ITAR, and Aviation Suppliers Association (ASA). All products are 100% inspected.
Quality Commitment »
Delivery of IN-STOCK orders ship same-day when order is placed before 2:00 PM EST.
Delivery dates for NON-STOCK items are estimates based on current backlog and are subject to confirmation at the time of order.
| NSN | Component Description |
|---|---|
| NSN 5360-01-499-3396 | Compression Helical Spring |
| NSN 2910-01-535-0384 | Metering And Distribut Fuel Pump |
| NSN 2910-01-535-0879 | Centrifugal Pump Impeller |
| NSN 4320-01-535-1278 | Pump Shaft Sleeve |
| NSN 5330-01-535-1517 | Gasket |
| NSN 3040-01-535-1518 | Straight Shaft |
| NSN 2935-01-535-1520 | Wearing Ring |
| NSN 6680-01-535-1521 | Volumetric Positive Displa Meter |
| NSN 1680-01-535-1522 | Mechan Transmission Housing Part |
| NSN 5340-01-535-1523 | Filler Opening Cap |
| NSN 1650-01-535-1524 | Hydraulic Motor-pump Yoke |
| NSN 5305-01-535-1525 | Setscrew |
| NSN 5330-01-535-1527 | Gasket |
| NSN 5310-01-535-1528 | Hexagon Self-locking Nut |
| NSN 4820-01-535-1529 | Valve Disk |
| NSN 2540-01-535-1530 | Vehicular Heater Control Valve |
| NSN 4820-01-535-1535 | Pilot Control Valve Parts Kit |
| NSN 4820-01-535-1537 | Pilot Control Valve Parts Kit |
| NSN 4820-01-535-1540 | Pilot Control Valve Parts Kit |
| NSN 9905-01-535-1944 | Identification Plate |
| NSN 9905-01-535-1950 | Identification Plate |
| NSN 9905-01-535-1952 | Identification Plate |
| NSN 9905-01-535-1953 | Identification Plate |
| NSN 9905-01-535-1954 | Identification Plate |
| NSN 9905-01-535-1956 | Identification Plate |
| NSN 9905-01-535-1958 | Identification Plate |
| NSN 9905-01-535-1960 | Identification Plate |
| NSN 9905-01-535-1970 | Identification Plate |
| NSN 9905-01-535-1971 | Identification Plate |
| NSN 9905-01-535-1972 | Identification Plate |
| NSN 9905-01-535-2169 | Identification Plate |
| NSN 9905-01-535-2198 | Identification Plate |
| NSN 9905-01-535-2199 | Identification Plate |
| NSN 9905-01-535-2200 | Identification Plate |
| NSN 9905-01-535-2201 | Identification Plate |
A washer having a centrally located hole with a solid or laminated cross-section and two flat parallel bearing surfaces. The hole must be 75 percent or less than the largest dimension and the bearing surface finish is greater than 32 microinch (0.8 micrometer). The thickness cannot exceed 25 percent of the largest outside dimension. When the largest outside dimension is less than 1/4 inch or 6mm, the thickness must be 0.006 inches (0.15mm) or greater and for items 1/4 inch (6mm) or larger, the thickness must be 0.016 inches (0.4mm) or greater. The maximum tolerance is applied to dimensions and used as a determining factor. Items with separable lamination use shim. For items fabricated from ceramic or electrically rated materials by specification or industry standards use insulator (1), washer. Excludes disk, valve, graphite impregnated and lubricated items.
Packing shall be accomplished to meet the performance test requirements of astm-d4169, distribution cycle 18, assurance level 1.
Packing shall be accomplished in accordance with table c.Ii for the packing level specified. closure, sealing and reinforcement shall be in accordance with the appropriate shipping container specification.
Options can be exercised as to specific method of preservation or dod approved packaging materials to be used. however, basic preservation method shall be retained, supplemental data shall be complied with, and unit package dimensions shall not be increased by more than one inch. equal or better protection shall be given the item and there shall be no increase in the package cost.
No special marking.
Physical protection.
No requirement.
No requirement.
No special type of cargo code applicable.
Bolts or nuts (iron or steel),(less than 35 feet).
Construction materials: includes paint and related materials, prefabricated building, wood products, metal and composition mater.
Shipment is not a consolidation and does not exceed 84 inches in any dimension.
Other or no special handling required (sh)
| 07/17 | 10/17 | 12/17 | 02/18 | 04/18 | 06/18 | 09/18 | 11/18 | 01/19 | 12/18 | 05/19 | 09/19 | 01/20 | 05/20 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 200.00 | 200.00 | 200.00 | 200.00 | 200.00 | 200.00 | 200.00 | 200.00 | 200.00 | 1112.00 | 1112.00 | 1112.00 | 1112.00 | 1112.00 |
| Code | Definition |
|---|---|
| FN | Factory New. Parts manufactured by the OEM and includes manufacturer certification. |
| NE | New. Parts manufactured by the OEM. May include manufacturer certification or company certification. |
| NS | New Surplus. New material item purchased from excess inventory. |
| OH | Overhauled. Product has been rebuilt and tested in accordance with the manufacturer's specifications by a repair shop (MRO). |
| SV | Serviceable product. |
| AR | As Removed. Product removed from aircraft or platform with no guarentee on the functionality of the part. |
| RP | Repairable. Product can be repaired by a MRO and be given a FAA 8130 or EASA Form 1 certification. |
| Part Number | RNVC | RNAAC | DAC | CAGE |
|---|---|---|---|---|
| 12759-01274 | 1 | ZZ | 5 | 0Y3H3 |
| 33008 | 2 | ZZ | 5 | 0Y3H3 |
| Name | No. Items | |||
|---|---|---|---|---|
| [You must be logged in to use lists] | ||||