change location
321-802-5889
321-733-7477
Model or part number: 20511224-1
Divergent Flap Slider NSN 5365-01-301-7871.
NSN 5365-01-301-7871 Datasheet
Factory New, New Material, New Surplus, Overhauled, Serviceable, Repairable, and AS Removed / Used material will be accompanied by a Certificate of Conformance, and any other documents/trace when applicable. We have a 7 year record retention.
We are committed to quality and follow an AS9120 quality management system. AeroBase Group is HAZMAT certified and registered with DDTC,
ITAR, and Aviation Suppliers Association (ASA). All products are 100% inspected.
Quality Commitment »
Delivery of IN-STOCK orders ship same-day when order is placed before 2:00 PM EST.
Delivery dates for NON-STOCK items are estimates based on current backlog and are subject to confirmation at the time of order.
| NSN | Component Description |
|---|---|
| NSN 4720-00-235-4131 | Nonmetallic Hose |
| NSN 2815-01-254-5358 | Diesel Engine Block Assembly |
| NSN 2815-01-271-3763 | Engine Poppet V Rocker Arm Shaft |
| NSN 4310-01-271-3807 | Compressor Crankshaft |
| NSN 4310-01-271-3808 | Compressor Cylinder Head |
| NSN 3040-01-271-3820 | Remote Control Lever |
| NSN 3040-01-271-3821 | Remote Control Lever |
| NSN 2815-01-271-5074 | Rocker Lever Shaft Support |
| NSN 5342-01-271-5088 | Engine Accessory Bracket |
| NSN 5342-01-271-5089 | Engine Accessory Bracket |
| NSN 2815-01-271-5096 | Engine Crankshaft |
| NSN 2815-01-271-5098 | Engine Poppet Valve Rocker Arm |
| NSN 2930-01-271-5102 | Fluid Cooler Core Assembly |
| NSN 4310-01-271-5103 | Compressor Piston |
| NSN 4720-01-271-6950 | Nonmetallic Hose |
| NSN 2815-01-271-7076 | Engine Vibration Dampener |
| NSN 4820-01-271-7079 | Valve Body |
| NSN 5342-01-271-7081 | Engine Accessory Bracket |
| NSN 2530-01-271-7084 | Brake Adjusting Screw Assembly |
| NSN 2990-01-271-7086 | Flywheel Housing Adapter |
| NSN 2520-01-271-7152 | Vehicular Clutch Disk |
| NSN 3040-01-271-7165 | Shaft Retaining Plate |
| NSN 4720-01-271-7995 | Nonmetallic Hose Assembly |
| NSN 4720-01-271-8000 | Nonmetallic Hose |
| NSN 2815-01-271-9792 | Piston Ring Set |
| NSN 2990-01-271-9816 | Belt-chain Tens Adjusting Device |
| NSN 5342-01-271-9818 | Engine Accessory Bracket |
| NSN 2815-01-271-9822 | Cylinder Sleeve And Piston Assem |
| NSN 2910-01-271-9826 | Fuel Injection No Cooling Sleeve |
| NSN 2530-01-272-0542 | Driving-nondriving Wheel Spindle |
| NSN 2530-01-272-2911 | Steering Pump Reservoir |
| NSN 2815-01-272-3954 | Engine Poppet Valve Rocker Cover |
| NSN 2815-01-272-5538 | Engine Valve Seat Insert |
| NSN 2815-01-272-5539 | Engine Valve Seat Insert |
| NSN 2815-01-272-6714 | Oil Pan |
A flat metal or plastic item of various peripheral shapes having a solid (not laminated) cross-section. It is designed to maintain a predetermined distance between two surfaces. For round items without a hole having a solid rectangular cross-section use disk, solid, plain. For round or hexagonal items with only one hole centrally located and with the length (thickness) exceeding 25 percent of the outside diameter or distance across peripheral flats, see spacer, sleeve. The thickness between the two parallel bearing surfaces must be 0.006 inch, (0.152 mm) or more for items less than 1/4 inch (6.35 mm) across the peripheral diameter, or smallest overall outside dimension, or must be 0.016 inch (0.406 mm) or more for items 1/4 inch (6.35 mm) or greater across the peripheral diameter or smallest overall outside dimension. For items with a thickness less than those indicated above, see shim. For items with one hole centrally located conforming to the above dimensional criteria use washer, flat or spacer, ring as applicable. When thickness and/or outside diameter or smallest overall outside dimension is designated as a tolerance/dimension the maximum dimension will be used to determine compliance. Excludes gasket; insulator (as modified) and mounting pad, electrical-electronic component.
Packing shall be accomplished to meet the performance test requirements of astm-d4169, distribution cycle 18, assurance level 1.
Packing shall be accomplished in accordance with table c.Ii for the packing level specified. closure, sealing and reinforcement shall be in accordance with the appropriate shipping container specification.
Options can be exercised as to specific method of preservation or dod approved packaging materials to be used. however, basic preservation method shall be retained, supplemental data shall be complied with, and unit package dimensions shall not be increased by more than one inch. equal or better protection shall be given the item and there shall be no increase in the package cost.
No special marking.
Physical protection.
No requirement.
No requirement.
Other Articles Of Iron Or Steel Not Wire Nesoi
Finished Metal Shapes
Articles Of Iron Or Steel, N.e.s.
No special type of cargo code applicable.
Metal hardware.
Construction materials: includes paint and related materials, prefabricated building, wood products, metal and composition mater.
Shipment is not a consolidation and does not exceed 84 inches in any dimension.
Other or no special handling required (sh)
| Code | Definition |
|---|---|
| FN | Factory New. Parts manufactured by the OEM and includes manufacturer certification. |
| NE | New. Parts manufactured by the OEM. May include manufacturer certification or company certification. |
| NS | New Surplus. New material item purchased from excess inventory. |
| OH | Overhauled. Product has been rebuilt and tested in accordance with the manufacturer's specifications by a repair shop (MRO). |
| SV | Serviceable product. |
| AR | As Removed. Product removed from aircraft or platform with no guarentee on the functionality of the part. |
| RP | Repairable. Product can be repaired by a MRO and be given a FAA 8130 or EASA Form 1 certification. |
| Part Number | RNVC | RNAAC | DAC | CAGE |
|---|---|---|---|---|
| 20511224-1 | 2 | KZ | A | 05MG0 |
| 20511224-1 | 2 | KZ | A | 47457 |
| Name | No. Items | |||
|---|---|---|---|---|
| [You must be logged in to use lists] | ||||