change location
321-802-5889
321-733-7477
Model or part number: 70219-03013-116
Differential Pinion NSN 5365-01-650-1649.
NSN 5365-01-650-1649 Datasheet
Factory New, New Material, New Surplus, Overhauled, Serviceable, Repairable, and AS Removed / Used material will be accompanied by a Certificate of Conformance, and any other documents/trace when applicable. We have a 7 year record retention.
We are committed to quality and follow an AS9120 quality management system. AeroBase Group is HAZMAT certified and registered with DDTC,
ITAR, and Aviation Suppliers Association (ASA). All products are 100% inspected.
Quality Commitment »
Delivery of IN-STOCK orders ship same-day when order is placed before 2:00 PM EST.
Delivery dates for NON-STOCK items are estimates based on current backlog and are subject to confirmation at the time of order.
| NSN | Component Description |
|---|---|
| NSN 1620-01-082-0688 | Landing Gear Yoke Assy |
| NSN 1615-01-268-9961 | Controllable Swashplate |
| NSN 5905-01-270-1696 | Nonwire Wound Variable Resistor |
| NSN 5950-01-279-5238 | Radio Frequency Coil |
| NSN 5950-01-279-5277 | Coil Form |
| NSN 5930-01-279-8032 | Push Switch |
| NSN 5930-01-279-8033 | Push Switch |
| NSN 5935-01-279-8038 | Electrical Connector Backshell |
| NSN 5935-01-279-8039 | Electrical Connector Backshell |
| NSN 5935-01-279-8632 | Electrical Connector Backshell |
| NSN 5935-01-279-9746 | Electrical Connector Backshell |
| NSN 5935-01-279-9747 | Electrical Connector Backshell |
| NSN 5935-01-279-9748 | Electrical Connector Backshell |
| NSN 5935-01-279-9749 | Electrical Connector Backshell |
| NSN 5935-01-280-1180 | Electrical Connector Shell |
| NSN 6150-01-292-1905 | E Special Purpose Cable Assembly |
| NSN 1560-01-292-1967 | Air Structural Component Support |
| NSN 5935-01-297-3264 | Electrical Connector Bracket |
| NSN 1560-01-297-3903 | Air Structural Component Support |
| NSN 4710-01-298-5517 | Metal Tube Assembly |
| NSN 1560-01-300-3063 | Air Structural Component Support |
| NSN 6150-01-304-6436 | Conductor Bus |
| NSN 1560-01-305-3983 | Access Door Insert |
| NSN 1560-01-305-7909 | Fuel Tank Parts Kit |
| NSN 1560-01-305-7910 | Fuel Tank Parts Kit |
| NSN 1560-01-305-7911 | Fuel Tank Parts Kit |
| NSN 1560-01-305-7912 | Fuel Tank Parts Kit |
| NSN 1560-01-306-0655 | Aircraft Structural Panel |
| NSN 5340-01-306-9079 | Access Cover |
| NSN 1560-01-307-0280 | Aircraft Structural Panel |
| NSN 5975-01-307-0289 | Electrical-electronic Equi Panel |
| NSN 5975-01-307-0290 | Electrical-electronic Equi Panel |
| NSN 5365-01-310-3992 | Plate Spacer |
| NSN 5365-01-310-4608 | Shim |
| NSN 5330-01-310-6522 | Wiper Ring |
A thin flat metal or plastic item of various peripheral shapes having a solid or laminated cross-section. It is designed to maintain a predetermined distance between two surfaces. For round items without a hole and having a solid rectangular cross-section use disk, solid, plain. Items with either (1) a solid (not laminated) cross-section, or (2) a non-separable laminated cross-section with one hole centrally located, must have a thickness less than 0.006 inch (0.152 mm) for items less than 1/4 inch (6.35 mm) outside diameter or shortest distance across peripheral flats, and less than 0.016 inch (0.406 mm) for items 1/4 inch (6.35 mm) or more outside diameter, or shortest distance across peripheral flats. for items with thickness greater than those indicated above, see spacer, plate; washer, flat and spacer, ring. when thickness and/or outside diameter or shortest distance across peripheral flats is designated as a tolerance dimension, the maximum dimension will be used to determine compliance. See also shim stock, laminated; shim stock assortment, gasket; and bearing, washer, thrust.
Packing shall be accomplished to meet the performance test requirements of astm-d4169, distribution cycle 18, assurance level 1.
Packing shall be accomplished in accordance with table c.Ii for the packing level specified. closure, sealing and reinforcement shall be in accordance with the appropriate shipping container specification.
Options can be exercised as to specific method of preservation or dod approved packaging materials to be used. however, basic preservation method shall be retained, supplemental data shall be complied with, and unit package dimensions shall not be increased by more than one inch. equal or better protection shall be given the item and there shall be no increase in the package cost.
No special marking.
Physical protection.
No requirement.
No special type of cargo code applicable.
Gaskets, (machinery and parts),(less than 35 feet).
Construction materials: includes paint and related materials, prefabricated building, wood products, metal and composition mater.
Shipment is not a consolidation and does not exceed 84 inches in any dimension.
Other or no special handling required (sh)
| Code | Definition |
|---|---|
| FN | Factory New. Parts manufactured by the OEM and includes manufacturer certification. |
| NE | New. Parts manufactured by the OEM. May include manufacturer certification or company certification. |
| NS | New Surplus. New material item purchased from excess inventory. |
| OH | Overhauled. Product has been rebuilt and tested in accordance with the manufacturer's specifications by a repair shop (MRO). |
| SV | Serviceable product. |
| AR | As Removed. Product removed from aircraft or platform with no guarentee on the functionality of the part. |
| RP | Repairable. Product can be repaired by a MRO and be given a FAA 8130 or EASA Form 1 certification. |
| Part Number | RNVC | RNAAC | DAC | CAGE |
|---|---|---|---|---|
| 70219-03013-116 | 2 | ZZ | C | 78286 |
| 70219-03013 | 9 | ZZ | C | 78286 |
| Name | No. Items | |||
|---|---|---|---|---|
| [You must be logged in to use lists] | ||||