change location
321-802-5889
321-733-7477
Model or part number: M23971/15-01
About this product
Hermetically sealed; 0.785 in. Lg; 0.575 in. W; 0.385 in. H; impedance 50 ohms; frequency range 0.1 to 400 mhz; voltage standing wave ratio 1.2 to 1 at 0.1 to 400 mhz; average coupling 3.0 plus 0.5 minus 0.0 db at 0.1 to 100 mhz,3.0 plus 0.75 minus 0.0 db at 100 to 200 mhz,3.0 plus 1.0 minus 0.0 db at 200 to 400 mhz; insertion loss 0.5 db at 0.1 to 100 mhz,0.75 db at 100 to 200 mhz,1.0 db at 200 to 400 mhz; isolation 15 db at 0.1 to 0.4 mhz,20 db at 0.4 to 2.0 mhz,30 db at 2.0 to 40 mhz,20 db at 40 to 400 mhz; phase balance porm 2 degrees at 0.1 to 100 mhz,porm 3 degrees at 100 to 200 mhz,porm 4 degrees at 200 to 400 mhz; amplitude balance porm 0.15 db at 0.1 to 100 mhz,porm 0.2 db at 100 to 200 mhz,porm 0.3 db at 200 to 400 mhz; power level 1 watt peak; operating temperature minus 55 degrees to plus 100 degrees celsius; pin terminals eight places 0.030 in. Dia
Tone Generator Board Connector Extender NSN 5985-01-230-9740.
NSN 5985-01-230-9740 Datasheet
Factory New, New Material, New Surplus, Overhauled, Serviceable, Repairable, and AS Removed / Used material will be accompanied by a Certificate of Conformance, and any other documents/trace when applicable. We have a 7 year record retention.
We are committed to quality and follow an AS9120 quality management system. AeroBase Group is HAZMAT certified and registered with DDTC,
ITAR, and Aviation Suppliers Association (ASA). All products are 100% inspected.
Quality Commitment »
Delivery of IN-STOCK orders ship same-day when order is placed before 2:00 PM EST.
Delivery dates for NON-STOCK items are estimates based on current backlog and are subject to confirmation at the time of order.
An item specifically designed to separate incoming radio frequency power into predetermined proportional values at its output terminals.
Packing shall be accomplished in accordance with table c.Ii for the packing level specified. closure, sealing and reinforcement shall be in accordance with applicable specification for shipping container.
Packing shall be accomplished in accordance with table c.Ii for the packing level specified. closure, sealing and reinforcement shall be in accordance with the appropriate shipping container specification.
Items or packages that require packing for acceptance by the carrier shall be packed in exterior type shipping containers in a manner that will ensure safe transportation at the lowest rate to the point of delivery and shall meet, as a minimum, the requirements of the following rules and regulations, as applicable to the mode(s) of transportation to be utilized: (a) postal regulations, (b) department of transportation regulations, (c) civil air regulations, (d) uniform freight classification rules, (e) national motor freight classification rules, (f) american truckers' association rules, (g) other applicable carriers' rules, (h) military air regulations for dangerous materials. consolidation of shipments. all exterior packs of 1.5 cubic feet or less having no single dimension (length, width, height) exceeding 40 inches (and when the total number of such containers in any individual shipment exceeds 25), shall be consolidated, using flat pallets, box pallets, or containers as the consolidating media. dangerous goods shall be prepared for shipment according to applicable department of transportation (dot) regulations and international regulations in effect at time of shipment. shipment by parcel post must comply with postal regulations.
Options can be exercised as to specific method of preservation or dod approved packaging materials to be used. however, basic preservation method shall be retained, supplemental data shall be complied with, and unit package dimensions shall not be increased by more than one inch. equal or better protection shall be given the item and there shall be no increase in the package cost.
No special marking.
Watervaporproof bag, sealed.
Ppp-c-795, cellular plastic film cushioning; or a-a-3129, open cell plastic cushioning; or ppp-c-1797, polypropylene foam cushioning; or a-a-59136, polyethylene foam cushioning.
No requirement.
Antenna & Antenna Reflectors Of All Kinds; Parts Suitable For Use Soley Or Principally W/ Apparatus Of Heading 8525 To 8528, Nesoi
Telecommunications Equipment
Parts Of Television Receivers, Radiobroadcast Receivers, Transmission Apparatus For Radio Telephony, Telegraphy, Broadcasting Or Television Etc.
No special type of cargo code applicable.
Radio parts and equipment, excluding tubes packed separately.
Instruments/equipment/supplies for radio, communications, electrical, laboratory, etc. (includes signal corps).
Shipment is not a consolidation and does not exceed 84 inches in any dimension.
Other or no special handling required (sh)
| Code | Definition |
|---|---|
| FN | Factory New. Parts manufactured by the OEM and includes manufacturer certification. |
| NE | New. Parts manufactured by the OEM. May include manufacturer certification or company certification. |
| NS | New Surplus. New material item purchased from excess inventory. |
| OH | Overhauled. Product has been rebuilt and tested in accordance with the manufacturer's specifications by a repair shop (MRO). |
| SV | Serviceable product. |
| AR | As Removed. Product removed from aircraft or platform with no guarentee on the functionality of the part. |
| RP | Repairable. Product can be repaired by a MRO and be given a FAA 8130 or EASA Form 1 certification. |
| Part Number | RNVC | RNAAC | DAC | CAGE |
|---|---|---|---|---|
| M23971/15-01 | 2 | TX | E | 81349 |
| MIL-P-23971/15 | 1 | TX | E | 81349 |
| Name | No. Items | |||
|---|---|---|---|---|
| [You must be logged in to use lists] | ||||