change location
321-802-5889
321-733-7477
Model or part number: DE1-0001
About this product
Power rating 100.0 kilowatts average; termination type connector recep-tacle; cooling method forced air; operating position horizontal
NSN 6150-01-306-2943 Datasheet
Factory New, New Material, New Surplus, Overhauled, Serviceable, Repairable, and AS Removed / Used material will be accompanied by a Certificate of Conformance, and any other documents/trace when applicable. We have a 7 year record retention.
We are committed to quality and follow an AS9120 quality management system. AeroBase Group is HAZMAT certified and registered with DDTC,
ITAR, and Aviation Suppliers Association (ASA). All products are 100% inspected.
Quality Commitment »
Delivery of IN-STOCK orders ship same-day when order is placed before 2:00 PM EST.
Delivery dates for NON-STOCK items are estimates based on current backlog and are subject to confirmation at the time of order.
| NSN | Component Description |
|---|---|
| NSN 6110-01-363-8817 | Meter Overload Module |
| NSN 6110-01-363-8818 | Supervisory Control Module |
| NSN 5940-01-369-6950 | Quick Disconnect Terminal |
| NSN 5940-01-369-6951 | Quick Disconnect Terminal |
A set (bank) of electrical elements that are passive (resistive, inductive, capacitive) or active (motors, batteries). They are usually located adjacent to each other to form a consolidated set of any of these elements or any combination of them. A load bank is used to replace distributed or dispersed load elements contained in a power distribution system or electrical network for the purpose of providing a concentrated load. A load bank contains all the essential electrical characteristics necessary to terminate the circuit and functions in the same manner as the load which it is intended to replace. This description necessarily includes a bank of light bulbs or cone heating elements where energy conversion is primarily in the form of heat although visible radiant energy is the natural result of incandescent heating. Load banks are intended to cover a specific range of characteristics and normally operate at dc or at power frequencies 50, 60, or 400 hz ac. Load banks may be uninstrumented or complete with integral instrumention and may also be furnished as skid or trailer mounted. Excludes test set, electrical (as modified). see also dummy load, electrical.
Packing shall be accomplished to meet the performance test requirements of astm-d4169, distribution cycle 18, assurance level 1.
Packing shall be accomplished in accordance with table c.Ii for the packing level specified. closure, sealing and reinforcement shall be in accordance with the appropriate shipping container specification.
Items or packages that require packing for acceptance by the carrier shall be packed in exterior type shipping containers in a manner that will ensure safe transportation at the lowest rate to the point of delivery and shall meet, as a minimum, the requirements of the following rules and regulations, as applicable to the mode(s) of transportation to be utilized: (a) postal regulations, (b) department of transportation regulations, (c) civil air regulations, (d) uniform freight classification rules, (e) national motor freight classification rules, (f) american truckers' association rules, (g) other applicable carriers' rules, (h) military air regulations for dangerous materials. consolidation of shipments. all exterior packs of 1.5 cubic feet or less having no single dimension (length, width, height) exceeding 40 inches (and when the total number of such containers in any individual shipment exceeds 25), shall be consolidated, using flat pallets, box pallets, or containers as the consolidating media. dangerous goods shall be prepared for shipment according to applicable department of transportation (dot) regulations and international regulations in effect at time of shipment. shipment by parcel post must comply with postal regulations.
Options can be exercised as to specific method of preservation or dod approved packaging materials to be used. however, basic preservation method shall be retained, supplemental data shall be complied with, and unit package dimensions shall not be increased by more than one inch. equal or better protection shall be given the item and there shall be no increase in the package cost.
No special marking.
Unheated general purpose.
Greaseproof-waterproof bag, sealed.
Electrical Machines and Apparatus Parts, Nesoi
Electric Apparatus
Parts Of Electrical Machines and Apparatus, Having Individual Functions, N.e.s.
No special type of cargo code applicable.
Communications/electronics, other than sigint/ew or comsec repair parts and components.
Arms/weapons (all types including inert component parts). when a 2" is indicated in the first position, then the special handlin.
Shipment is not a consolidation, but does exceed 84 inches in one or more dimensions.
Moderate sensitivity, category iii, aa&e, unclassified
| Code | Definition |
|---|---|
| FN | Factory New. Parts manufactured by the OEM and includes manufacturer certification. |
| NE | New. Parts manufactured by the OEM. May include manufacturer certification or company certification. |
| NS | New Surplus. New material item purchased from excess inventory. |
| OH | Overhauled. Product has been rebuilt and tested in accordance with the manufacturer's specifications by a repair shop (MRO). |
| SV | Serviceable product. |
| AR | As Removed. Product removed from aircraft or platform with no guarentee on the functionality of the part. |
| RP | Repairable. Product can be repaired by a MRO and be given a FAA 8130 or EASA Form 1 certification. |
| Part Number | RNVC | RNAAC | DAC | CAGE |
|---|---|---|---|---|
| DE1-0001 | 9 | PA | 4 | 17023 |
| Name | No. Items | |||
|---|---|---|---|---|
| [You must be logged in to use lists] | ||||