change location
321-802-5889
321-733-7477
Model or part number: 11442279
About this product
Case al alloy 6061 temper t6, per qq-a-250/11 or equiv; chemical conversion coating per mil-c-5541 class 3; and paint; exc connectors shall be iaw mil-c-39012; one input and three output sma female connectors; two way power division; four mtg holes 0.123 to 0.133 in. Dia. On 1.400 in. By 2.550 in. Mtg ctr; any phase, at each output; impedance 50 ohms; insertion loss per inspection: 4 porm 0.2 db; coupling per inspection: 10.0 porm 0.5 db; isolation per inspection: 20.0 db min; operating temp. Range: m46 to p71 deg c; storage temp. Range: m46 to p71 deg c; altitude range: 8000 ft; operating life: 2000 hrs min; shielded to prevent rf leakage; test rqmt for life; rf leakage, shock, vibration, humidity and moisture resistance, altitude, high and low, thermal shock, salt sea atmosphere, resistance to solvents,fungus and elec end points; enviorments per mil-std-202 and mil-std-810
Tone Generator Board Connector Extender NSN 6625-01-223-6350.
NSN 6625-01-223-6350 Datasheet
Factory New, New Material, New Surplus, Overhauled, Serviceable, Repairable, and AS Removed / Used material will be accompanied by a Certificate of Conformance, and any other documents/trace when applicable. We have a 7 year record retention.
We are committed to quality and follow an AS9120 quality management system. AeroBase Group is HAZMAT certified and registered with DDTC,
ITAR, and Aviation Suppliers Association (ASA). All products are 100% inspected.
Quality Commitment »
Delivery of IN-STOCK orders ship same-day when order is placed before 2:00 PM EST.
Delivery dates for NON-STOCK items are estimates based on current backlog and are subject to confirmation at the time of order.
An item specifically designed to separate incoming radio frequency power into predetermined proportional values at its output terminals.
Packing shall be accomplished in accordance with table c.Ii for the packing level specified. closure, sealing and reinforcement shall be in accordance with applicable specification for shipping container.
Packing shall be accomplished in accordance with table c.Ii for the packing level specified. closure, sealing and reinforcement shall be in accordance with the appropriate shipping container specification.
Items or packages that require packing for acceptance by the carrier shall be packed in exterior type shipping containers in a manner that will ensure safe transportation at the lowest rate to the point of delivery and shall meet, as a minimum, the requirements of the following rules and regulations, as applicable to the mode(s) of transportation to be utilized: (a) postal regulations, (b) department of transportation regulations, (c) civil air regulations, (d) uniform freight classification rules, (e) national motor freight classification rules, (f) american truckers' association rules, (g) other applicable carriers' rules, (h) military air regulations for dangerous materials. consolidation of shipments. all exterior packs of 1.5 cubic feet or less having no single dimension (length, width, height) exceeding 40 inches (and when the total number of such containers in any individual shipment exceeds 25), shall be consolidated, using flat pallets, box pallets, or containers as the consolidating media. dangerous goods shall be prepared for shipment according to applicable department of transportation (dot) regulations and international regulations in effect at time of shipment. shipment by parcel post must comply with postal regulations.
Options can be exercised as to specific method of preservation or dod approved packaging materials to be used. however, basic preservation method shall be retained, supplemental data shall be complied with, and unit package dimensions shall not be increased by more than one inch. equal or better protection shall be given the item and there shall be no increase in the package cost.
No special marking.
Watervaporproof bag, sealed.
Ppp-c-795, cellular plastic film cushioning; or a-a-3129, open cell plastic cushioning; or ppp-c-1797, polypropylene foam cushioning; or a-a-59136, polyethylene foam cushioning.
No requirement.
Parts and Accessories Of Articles Of Schedule B Subheading 9030.39
Measuring, Testing, Control Instruments
Parts and Accessories For Instruments and Apparatus (except Meters) Measuring Etc. Electrical Quanities and Devices Measuring Etc. Ionized Radiations
No special type of cargo code applicable.
Electrical appliances, small.
Instruments/equipment/supplies for radio, communications, electrical, laboratory, etc. (includes signal corps).
Shipment is not a consolidation and does not exceed 84 inches in any dimension.
Other or no special handling required (sh)
| 04/16 |
|---|
| 6.00 |
| Code | Definition |
|---|---|
| FN | Factory New. Parts manufactured by the OEM and includes manufacturer certification. |
| NE | New. Parts manufactured by the OEM. May include manufacturer certification or company certification. |
| NS | New Surplus. New material item purchased from excess inventory. |
| OH | Overhauled. Product has been rebuilt and tested in accordance with the manufacturer's specifications by a repair shop (MRO). |
| SV | Serviceable product. |
| AR | As Removed. Product removed from aircraft or platform with no guarentee on the functionality of the part. |
| RP | Repairable. Product can be repaired by a MRO and be given a FAA 8130 or EASA Form 1 certification. |
| Part Number | RNVC | RNAAC | DAC | CAGE |
|---|---|---|---|---|
| 11442279 | 2 | TX | 5 | 12457 |
| 11442279 | 2 | TX | A | 18876 |
| C01208 | 2 | TX | 5 | 64537 |
| 11442279 | 2 | TX | 6 | 3B150 |
| 11442279 | 9 | TX | 6 | 49956 |
| 11442279 | 2 | ZZ | 5 | 54X10 |
| Name | No. Items | |||
|---|---|---|---|---|
| [You must be logged in to use lists] | ||||