change location
321-802-5889
321-733-7477
Model or part number: WSE-7
About this product
One end is threaded
Adjusting Stud Shaft NSN 3040-01-582-2882.
NSN 3040-01-582-2882 Datasheet
Factory New, New Material, New Surplus, Overhauled, Serviceable, Repairable, and AS Removed / Used material will be accompanied by a Certificate of Conformance, and any other documents/trace when applicable. We have a 7 year record retention.
We are committed to quality and follow an AS9120 quality management system. AeroBase Group is HAZMAT certified and registered with DDTC,
ITAR, and Aviation Suppliers Association (ASA). All products are 100% inspected.
Quality Commitment »
Delivery of IN-STOCK orders ship same-day when order is placed before 2:00 PM EST.
Delivery dates for NON-STOCK items are estimates based on current backlog and are subject to confirmation at the time of order.
| NSN | Component Description |
|---|---|
| NSN 5306-01-582-0676 | Eccentric Head Bolt |
| NSN 2510-01-582-0691 | Vehicular Door Lock Set |
| NSN 5365-01-582-0695 | Shim |
| NSN 2540-01-582-0697 | Vehicular Door Latch |
| NSN 5365-01-582-0720 | Shim |
| NSN 2510-01-582-0725 | Vehicular Door Hinge |
| NSN 3030-01-582-0731 | V Belt |
| NSN 6150-01-582-0733 | Wiring Harness |
| NSN 6150-01-582-0736 | Wiring Harness |
| NSN 6150-01-582-0737 | Wiring Harness |
| NSN 6150-01-582-0739 | Wiring Harness |
| NSN 6150-01-582-0740 | Wiring Harness |
| NSN 6150-01-582-0999 | Wiring Harness |
| NSN 5340-01-582-1012 | Retaining Strap |
| NSN 5940-01-582-1045 | Lug Terminal |
| NSN 5330-01-582-1133 | Gasket |
| NSN 5330-01-582-1134 | Gasket |
| NSN 5330-01-582-1137 | Gasket |
| NSN 2510-01-582-1974 | Engine Mount Bracket |
| NSN 2540-01-582-1983 | Compartment Vehicular Heater |
| NSN 9340-01-582-1993 | Single Plate Safety Glass |
| NSN 2510-01-582-1998 | Vehicular Window |
| NSN 2590-01-582-2001 | Vehicular Components Bracket |
| NSN 3040-01-582-2882 | Straight Shaft |
| NSN 5330-01-582-2888 | Gasket |
| NSN 2541-01-582-3336 | Vehicular Wind Transparent Armor |
| NSN 2510-01-586-3654 | Vehicul Structural Frame Section |
| NSN 2510-01-586-3665 | Vehicul Structural Frame Section |
| NSN 2510-01-586-3959 | Vehicul Structural Frame Section |
| NSN 2541-01-586-3974 | Vehicular Window Armor Frame |
| NSN 2590-01-586-3983 | Metal Molding |
| NSN 2540-01-586-3987 | Vehicular Door Handle |
| NSN 2540-01-586-3992 | Vehicular Insulation |
| NSN 2540-01-586-3997 | Vehicular Insulation |
| NSN 2540-01-586-4002 | Vehicular Insulation |
A straight shaft having two or more of the following conditions: a specified surface finish designation in the range of 1 to 125 microinches (o.O25 to 3.2 micrometers), arithmetical average (aa), machined peripheral flat(s), circular groove (s), keyway(s), splines, threads, or holes. It is not designed for use in aligning by fitting into corresponding holes of another item. It may be drilled for lubricating holes. For items having an integral gear(s) or worm(s), see gearshaft (as modified). For items designed to support rotating members see axle(1), straight. For items not having the above conditions see pin, straight, headless. For items having machined ends which constitute steps see shaft(1), shouldered; axle(1), shouldered; and bolt, fluid passage.
Packing shall be accomplished to meet the performance test requirements of astm-d4169, distribution cycle 18, assurance level 1.
Packing shall be accomplished in accordance with table c.Ii for the packing level specified. closure, sealing and reinforcement shall be in accordance with the appropriate shipping container specification.
Options can be exercised as to specific method of preservation or dod approved packaging materials to be used. however, basic preservation method shall be retained, supplemental data shall be complied with, and unit package dimensions shall not be increased by more than one inch. equal or better protection shall be given the item and there shall be no increase in the package cost.
No special marking.
Physical protection.
Ppp-c-795, cellular plastic film cushioning; or a-a-3129, open cell plastic cushioning; or ppp-c-1797, polypropylene foam cushioning; or a-a-59136, polyethylene foam cushioning.
No requirement.
Transmission Shafts and Cranks, Except Camshafts and Crankshafts
Industrial Machines, Other
Transmission Shafts (including Cam and Crank Shafts) and Cranks
No special type of cargo code applicable.
Motors and parts, (machinery and parts),(less than 35 feet).
Trailers, vehicles, machinery, shop and warehouse equipment and supplies including special tools and equipment, ground servicing.
Shipment is not a consolidation and does not exceed 84 inches in any dimension.
Other or no special handling required (sh)
| Code | Definition |
|---|---|
| FN | Factory New. Parts manufactured by the OEM and includes manufacturer certification. |
| NE | New. Parts manufactured by the OEM. May include manufacturer certification or company certification. |
| NS | New Surplus. New material item purchased from excess inventory. |
| OH | Overhauled. Product has been rebuilt and tested in accordance with the manufacturer's specifications by a repair shop (MRO). |
| SV | Serviceable product. |
| AR | As Removed. Product removed from aircraft or platform with no guarentee on the functionality of the part. |
| RP | Repairable. Product can be repaired by a MRO and be given a FAA 8130 or EASA Form 1 certification. |
| Part Number | RNVC | RNAAC | DAC | CAGE |
|---|---|---|---|---|
| WSE-7 | 2 | ZZ | E | 31UG4 |
| Name | No. Items | |||
|---|---|---|---|---|
| [You must be logged in to use lists] | ||||