change location
321-802-5889
321-733-7477
Model or part number: 232-36319-2
Riveting Burr NSN 5310-01-126-0112.
NSN 5310-01-126-0112 Datasheet
Factory New, New Material, New Surplus, Overhauled, Serviceable, Repairable, and AS Removed / Used material will be accompanied by a Certificate of Conformance, and any other documents/trace when applicable. We have a 7 year record retention.
We are committed to quality and follow an AS9120 quality management system. AeroBase Group is HAZMAT certified and registered with DDTC,
ITAR, and Aviation Suppliers Association (ASA). All products are 100% inspected.
Quality Commitment »
Delivery of IN-STOCK orders ship same-day when order is placed before 2:00 PM EST.
Delivery dates for NON-STOCK items are estimates based on current backlog and are subject to confirmation at the time of order.
| NSN | Component Description |
|---|---|
| NSN 5999-00-089-4233 | Electrical Shield Plate |
| NSN 6625-00-204-5977 | Test Adapter |
| NSN 5841-00-235-7719 | Radar Set Subassembly |
| NSN 5841-00-235-7720 | Radar Set Subassembly |
| NSN 5998-00-378-4095 | Electronic Test Extender Card |
| NSN 5998-00-378-4096 | Electronic Test Extender Card |
| NSN 6220-00-500-8555 | Light Transmitt Indicating Panel |
| NSN 3020-00-729-4215 | Spur Gear |
| NSN 4320-00-910-6150 | Hydraulic Jack Ram |
| NSN 1290-00-937-8053 | Fire Control Eq Modification Kit |
| NSN 6625-01-036-0286 | Regulator Tester |
| NSN 5998-01-113-5465 | Circuit Card Assembly |
| NSN 5961-01-115-5168 | Transistor |
| NSN 1440-01-124-6607 | Guided Miss Structural Component |
| NSN 5310-01-126-0112 | Flat Washer |
| NSN 5340-01-126-0119 | Sliding Block |
| NSN 5340-01-126-2261 | Spacing Threaded Standoff |
| NSN 5340-01-126-2273 | Mounting Plate |
| NSN 5340-01-126-2274 | Pipe Covering Protection Saddle |
| NSN 5342-01-126-2279 | Quick Release Pin Receptacle |
| NSN 2995-01-126-5007 | Valve Cap |
| NSN 5365-01-127-6585 | Shim |
| NSN 5998-01-135-5844 | Electronic Components Assembly |
| NSN 1270-01-171-0901 | Dessicator Assembly |
| NSN 5998-01-233-6701 | Circuit Card Assembly |
| NSN 5998-01-233-6702 | Circuit Card Assembly |
| NSN 9905-01-236-9883 | Instruction Plate |
| NSN 1730-01-273-0912 | Tie Strap Assembly |
| NSN 5985-01-280-4835 | Antenna Assembly |
| NSN 5865-01-281-3114 | Oscillator Cam |
| NSN 5962-01-282-3957 | Linear Microcircuit |
| NSN 5962-01-282-3958 | Digital Microcircuit |
| NSN 9905-01-288-0283 | Identification Plate |
| NSN 5825-01-289-7025 | Cancellation Subassembly Bridge |
| NSN 5985-01-304-6870 | Waveguide Adapter |
A washer having a centrally located hole with a solid or laminated cross-section and two flat parallel bearing surfaces. The hole must be 75 percent or less than the largest dimension and the bearing surface finish is greater than 32 microinch (0.8 micrometer). The thickness cannot exceed 25 percent of the largest outside dimension. When the largest outside dimension is less than 1/4 inch or 6mm, the thickness must be 0.006 inches (0.15mm) or greater and for items 1/4 inch (6mm) or larger, the thickness must be 0.016 inches (0.4mm) or greater. The maximum tolerance is applied to dimensions and used as a determining factor. Items with separable lamination use shim. For items fabricated from ceramic or electrically rated materials by specification or industry standards use insulator (1), washer. Excludes disk, valve, graphite impregnated and lubricated items.
Packing shall be accomplished to meet the performance test requirements of astm-d4169, distribution cycle 18, assurance level 1.
Packing shall be accomplished in accordance with table c.Ii for the packing level specified. closure, sealing and reinforcement shall be in accordance with the appropriate shipping container specification.
Options can be exercised as to specific method of preservation or dod approved packaging materials to be used. however, basic preservation method shall be retained, supplemental data shall be complied with, and unit package dimensions shall not be increased by more than one inch. equal or better protection shall be given the item and there shall be no increase in the package cost.
No special marking.
Physical protection.
No requirement.
No requirement.
Gaskets, Washers & Other Seals
Other Industrial Supplies
Articles Of Plastics, N.e.s.
No special type of cargo code applicable.
Metal hardware.
Construction materials: includes paint and related materials, prefabricated building, wood products, metal and composition mater.
Shipment is not a consolidation and does not exceed 84 inches in any dimension.
Other or no special handling required (sh)
| 12/15 | 04/16 | 09/16 | 02/17 | 07/17 | 12/18 |
|---|---|---|---|---|---|
| 62.00 | 62.00 | 62.00 | 62.00 | 62.00 | 80.00 |
| Code | Definition |
|---|---|
| FN | Factory New. Parts manufactured by the OEM and includes manufacturer certification. |
| NE | New. Parts manufactured by the OEM. May include manufacturer certification or company certification. |
| NS | New Surplus. New material item purchased from excess inventory. |
| OH | Overhauled. Product has been rebuilt and tested in accordance with the manufacturer's specifications by a repair shop (MRO). |
| SV | Serviceable product. |
| AR | As Removed. Product removed from aircraft or platform with no guarentee on the functionality of the part. |
| RP | Repairable. Product can be repaired by a MRO and be given a FAA 8130 or EASA Form 1 certification. |
| Part Number | RNVC | RNAAC | DAC | CAGE |
|---|---|---|---|---|
| 232-36319-2 | 2 | ZZ | 2 | 98748 |
| 232-36319-2 | 2 | ZZ | 1 | 82918 |
| Name | No. Items | |||
|---|---|---|---|---|
| [You must be logged in to use lists] | ||||