change location
321-802-5889
321-733-7477
Model or part number: 3H0467
About this product
Washer for ft0576 tool group used for removal of recoil spring when front pilot is broken and to control expansion after front cover has been removed
Riveting Burr NSN 5310-01-526-7006.
NSN 5310-01-526-7006 Datasheet
Factory New, New Material, New Surplus, Overhauled, Serviceable, Repairable, and AS Removed / Used material will be accompanied by a Certificate of Conformance, and any other documents/trace when applicable. We have a 7 year record retention.
We are committed to quality and follow an AS9120 quality management system. AeroBase Group is HAZMAT certified and registered with DDTC,
ITAR, and Aviation Suppliers Association (ASA). All products are 100% inspected.
Quality Commitment »
Delivery of IN-STOCK orders ship same-day when order is placed before 2:00 PM EST.
Delivery dates for NON-STOCK items are estimates based on current backlog and are subject to confirmation at the time of order.
| NSN | Component Description |
|---|---|
| NSN 3805-01-026-9552 | Meter Group |
| NSN 2510-01-182-0858 | Left Side Hood Guard Assembly |
| NSN 2815-01-371-6886 | Valve Stem Guide |
| NSN 2510-01-443-2974 | Vehicular Body Panel |
| NSN 2990-01-443-5133 | Lubrication Plate |
| NSN 2530-01-493-8724 | Track Shoe Assembly |
| NSN 4730-01-518-2422 | Hose Clamp |
| NSN 4710-01-518-2440 | Metal Tube Assembly |
| NSN 4320-01-518-5731 | Hydraulic Pump |
| NSN 4030-01-525-1233 | Hook Safety Latch |
| NSN 5310-01-526-7006 | Flat Washer |
| NSN 5340-01-527-6992 | Rod End Connector |
| NSN 5315-01-527-6994 | Headless Straight Pin |
| NSN 5365-01-527-6997 | Sleeve Spacer |
| NSN 5340-01-527-7520 | Angle Bracket |
| NSN 5340-01-527-7829 | Angle Bracket Set |
| NSN 5340-01-527-8593 | Lever Bracket |
| NSN 5340-01-527-8826 | Loop Clamp |
| NSN 5340-01-527-9809 | Mounting Bracket |
| NSN 5342-01-527-9912 | Engine Accessory Bracket |
| NSN 5340-01-527-9921 | Mounting Bracket |
| NSN 2590-01-527-9937 | Vehicular Components Bracket |
| NSN 2520-01-527-9942 | Transmission Support Ring |
| NSN 2930-01-527-9943 | Radiator Fan Shroud |
| NSN 5340-01-528-1011 | Angle Bracket |
| NSN 5120-01-531-1452 | Torque Screwdriver |
A washer having a centrally located hole with a solid or laminated cross-section and two flat parallel bearing surfaces. The hole must be 75 percent or less than the largest dimension and the bearing surface finish is greater than 32 microinch (0.8 micrometer). The thickness cannot exceed 25 percent of the largest outside dimension. When the largest outside dimension is less than 1/4 inch or 6mm, the thickness must be 0.006 inches (0.15mm) or greater and for items 1/4 inch (6mm) or larger, the thickness must be 0.016 inches (0.4mm) or greater. The maximum tolerance is applied to dimensions and used as a determining factor. Items with separable lamination use shim. For items fabricated from ceramic or electrically rated materials by specification or industry standards use insulator (1), washer. Excludes disk, valve, graphite impregnated and lubricated items.
Packing shall be accomplished to meet the performance test requirements of astm-d4169, distribution cycle 18, assurance level 1.
Packing shall be accomplished in accordance with table c.Ii for the packing level specified. closure, sealing and reinforcement shall be in accordance with the appropriate shipping container specification.
Options can be exercised as to specific method of preservation or dod approved packaging materials to be used. however, basic preservation method shall be retained, supplemental data shall be complied with, and unit package dimensions shall not be increased by more than one inch. equal or better protection shall be given the item and there shall be no increase in the package cost.
No special marking.
Physical protection.
No requirement.
No requirement.
No special type of cargo code applicable.
Metal and metal products, nos, (less than 35 feet).
Trailers, vehicles, machinery, shop and warehouse equipment and supplies including special tools and equipment, ground servicing.
Shipment is not a consolidation and does not exceed 84 inches in any dimension.
Other or no special handling required (sh)
| Code | Definition |
|---|---|
| FN | Factory New. Parts manufactured by the OEM and includes manufacturer certification. |
| NE | New. Parts manufactured by the OEM. May include manufacturer certification or company certification. |
| NS | New Surplus. New material item purchased from excess inventory. |
| OH | Overhauled. Product has been rebuilt and tested in accordance with the manufacturer's specifications by a repair shop (MRO). |
| SV | Serviceable product. |
| AR | As Removed. Product removed from aircraft or platform with no guarentee on the functionality of the part. |
| RP | Repairable. Product can be repaired by a MRO and be given a FAA 8130 or EASA Form 1 certification. |
| Part Number | RNVC | RNAAC | DAC | CAGE |
|---|---|---|---|---|
| 3H0467 | 2 | ZZ | E | 11083 |
| Name | No. Items | |||
|---|---|---|---|---|
| [You must be logged in to use lists] | ||||