change location
321-802-5889
321-733-7477
Model or part number: 9363100
This product is available in the following quantities and conditions.
Total: 215 Note: Availability of this item was last updated 08/15/2024, and may have changed since then. Request a quote for up to date pricing and availability.
Divergent Flap Slider NSN 5365-01-204-4093.
NSN 5365-01-204-4093 Datasheet
Factory New, New Material, New Surplus, Overhauled, Serviceable, Repairable, and AS Removed / Used material will be accompanied by a Certificate of Conformance, and any other documents/trace when applicable. We have a 7 year record retention.
We are committed to quality and follow an AS9120 quality management system. AeroBase Group is HAZMAT certified and registered with DDTC,
ITAR, and Aviation Suppliers Association (ASA). All products are 100% inspected.
Quality Commitment »
Delivery of IN-STOCK orders ship same-day when order is placed before 2:00 PM EST.
Delivery dates for NON-STOCK items are estimates based on current backlog and are subject to confirmation at the time of order.
| NSN | Component Description |
|---|---|
| NSN 6920-01-147-8589 | Target Training Set Track System |
| NSN 5930-01-161-3560 | Proximity Switch |
| NSN 5340-01-161-3633 | Mounting Bracket |
| NSN 6920-01-161-8654 | Track And Drive Mechanism Assemb |
| NSN 3010-01-161-8656 | Line Electro-mechanical Actuator |
| NSN 5998-01-161-8659 | Electrical Card Holder |
| NSN 5340-01-161-8662 | Mounting Plate |
| NSN 5340-01-161-8663 | Mounting Bracket |
| NSN 6920-01-161-8664 | Drive End Track Assembly |
| NSN 5995-01-161-8754 | E Special Purpose Cable Assembly |
| NSN 3030-01-161-8784 | V Belting |
| NSN 3020-01-161-8827 | Cone Pulley |
| NSN 3040-01-161-8842 | Shaft Collar |
| NSN 6150-01-161-8856 | E Special Purpose Cable Assembly |
| NSN 5975-01-161-8861 | Electrical-electronic Eq Chassis |
| NSN 5340-01-161-8880 | Clamping Catch |
| NSN 6920-01-161-8886 | Return End Track Assembly |
| NSN 5998-01-161-8894 | Circuit Card Assembly |
| NSN 3040-01-166-1107 | Straight Shaft |
| NSN 3040-01-167-6586 | Straight Shaft |
| NSN 5365-01-176-0738 | Tolerance Ring |
| NSN 5340-01-195-6665 | Mounting Bracket |
| NSN 5340-01-199-8779 | Retaining Strap |
| NSN 5975-01-203-2770 | Cable Hanger |
| NSN 4010-01-203-7459 | Single Leg Wire Rope Assembly |
| NSN 5330-01-204-4043 | Gasket |
| NSN 3020-01-204-4057 | Groove Pulley |
| NSN 5340-01-204-4074 | Angle Bracket |
| NSN 5365-01-204-4093 | Plate Spacer |
| NSN 5995-01-231-4791 | E Special Purpose Cable Assembly |
| NSN 6920-01-384-6675 | Propane C Shield Holder Assembly |
| NSN 6920-01-392-0435 | Target Rail |
| NSN 3950-01-392-2327 | Monorail Trolley |
A flat metal or plastic item of various peripheral shapes having a solid (not laminated) cross-section. It is designed to maintain a predetermined distance between two surfaces. For round items without a hole having a solid rectangular cross-section use disk, solid, plain. For round or hexagonal items with only one hole centrally located and with the length (thickness) exceeding 25 percent of the outside diameter or distance across peripheral flats, see spacer, sleeve. The thickness between the two parallel bearing surfaces must be 0.006 inch, (0.152 mm) or more for items less than 1/4 inch (6.35 mm) across the peripheral diameter, or smallest overall outside dimension, or must be 0.016 inch (0.406 mm) or more for items 1/4 inch (6.35 mm) or greater across the peripheral diameter or smallest overall outside dimension. For items with a thickness less than those indicated above, see shim. For items with one hole centrally located conforming to the above dimensional criteria use washer, flat or spacer, ring as applicable. When thickness and/or outside diameter or smallest overall outside dimension is designated as a tolerance/dimension the maximum dimension will be used to determine compliance. Excludes gasket; insulator (as modified) and mounting pad, electrical-electronic component.
Packing shall be accomplished to meet the performance test requirements of astm-d4169, distribution cycle 18, assurance level 1.
Packing shall be accomplished in accordance with table c.Ii for the packing level specified. closure, sealing and reinforcement shall be in accordance with the appropriate shipping container specification.
Options can be exercised as to specific method of preservation or dod approved packaging materials to be used. however, basic preservation method shall be retained, supplemental data shall be complied with, and unit package dimensions shall not be increased by more than one inch. equal or better protection shall be given the item and there shall be no increase in the package cost.
No special marking.
Physical protection.
No requirement.
No requirement.
No special type of cargo code applicable.
Metal hardware.
Trailers, vehicles, machinery, shop and warehouse equipment and supplies including special tools and equipment, ground servicing.
Shipment is not a consolidation and does not exceed 84 inches in any dimension.
Other or no special handling required (sh)
| Code | Definition |
|---|---|
| FN | Factory New. Parts manufactured by the OEM and includes manufacturer certification. |
| NE | New. Parts manufactured by the OEM. May include manufacturer certification or company certification. |
| NS | New Surplus. New material item purchased from excess inventory. |
| OH | Overhauled. Product has been rebuilt and tested in accordance with the manufacturer's specifications by a repair shop (MRO). |
| SV | Serviceable product. |
| AR | As Removed. Product removed from aircraft or platform with no guarentee on the functionality of the part. |
| RP | Repairable. Product can be repaired by a MRO and be given a FAA 8130 or EASA Form 1 certification. |
| Part Number | RNVC | RNAAC | DAC | CAGE |
|---|---|---|---|---|
| 9363100 | 2 | BF | 2 | 19200 |
| Name | No. Items | |||
|---|---|---|---|---|
| [You must be logged in to use lists] | ||||